Learn How to Mix Gas and Oil for Weedeater?

Weed eaters are powerful machines and can cut the hardest weed with just one pass. Among all types of weed eaters, gas powered models are certainly the best for heavy duties. However, these power tools require proper maintenance to deliver their maximum power. So how to mix gas and oil for weedeater?

Dosing the optimal gas and oil mixture is part of that maintenance. Many people usually blame the motor for the loss of power in their string trimmers. However, most of the time, the real cause of the problem is the use of a wrong mix.

In this article you’ll find a step-by-step guide to learn how to mix gas and oil to get the most out of your weed eater.

Learn How to Mix Gas and Oil for Weedeater?

What is Weed Eater?

A weed eater, also known as string trimmer, is a machine used to cut grass and weeds. It uses a sturdy nylon string that cuts weed while it rotates. Weed eaters can work with electric or gas powered engines.

Gas powered weed eaters are the most efficient and powerful. They also provide greater freedom of movement because they don’t depend on a nearby outlet to operate. However, they’re quite noisy and emit polluting gases.

Gas powered weed eaters tend to collect too much dust inside the air filters. In addition, lubricant oil needs to be changed so frequently. So, the maintenance costs in these cases are higher in contrast to other models.

What is Weed Eater?

On the other hand, electric weed eaters are quieter and less polluting. Electric devices use brushless motors to work. These types of motors generate less friction between the rotor and the stator, preventing overheating and waste production. Therefore, electric motors need less maintenance than their gas powered counterparts.

Electric weed eaters can be wired or wireless. Wired models use a power cord plugged into an outlet. On the other hand, wireless models use rechargeable lithium batteries to operate.

Lithium batteries are very practical because they allow you to cut weed in remote areas, where outlets aren’t available. However, these batteries tend to discharge too quickly, providing up to 2 hours of continuous service.

Also, they take a long time to recharge and can explode if overheated or scratched. So, you must be careful when using a wireless weed eater.

Step by Step Guide to Mix Gas and Oil for Weed Eater

Step by Step Guide to Mix Gas and Oil for Weed Eater

Mixing gas and oil to put a weed eater to work isn’t as complicated as it seems. You just need to follow a series of steps to get the job done. This is what you need to do:

  1. First of all, read the user manual. If you don’t have it, you can also find it on the official website of the product. While reading the instructions, verify that the product really requires the gas and the oil to be mixed. Newest models have oil tanks to automatically make the mix.
  2. Use a clean, sturdy container to make the mix. Never use a milk carton for this purpose. The walls and lid of the container must be thick enough to contain the fuel vapors.
  3. Also, make sure to use the appropriate gas type. Some low cost options generate too much waste when burned, reducing the lifespan of the motor.
  4. Only apply the kind of oil recommended by the manufacturer. Using something different may considerably reduce the engine performance.
  5. Then, mix the gas and the oil at the proper volume ratio. 40:1 and 50:1 are usually the most common mixing ratios used on weed eaters.
  6. Finally, fill the fuel tank with the mix, turn on the engine and get down to work.

Conclusion

As you can see, you need the proper oil-gas mix to get the most out of your cutting tool. To do it, you don’t need previous experience or fancy tools. Just carefully follow each step and everything will be fine.

Also remember to use a container with thick and sturdy walls to make the mix. In addition, only use top quality products for the best results.

You can learn more Step by Step Guide to Learn How to Use A Weed Eater

Leave a Reply

Your email address will not be published. Required fields are marked *

About Us

You certainly can’t believe everything the Internet tells you. Kelvin David knows this better than anyone. A few years ago, Kelvin decided to try online shopping for the first time. He was looking for a new electric drill he could use on his daily work as a contractor.